English Version 1.1
User’s Manual 9 2. Connecting the PTZ Camera Please refer to the sections below for details of how to set and connect the PTZ
User’s Manual 10 2.2 Switch Definition The PTZ Camera ID and communication protocol must be configured before connecting the ca
User’s Manual 11 be the same. The default RS-485 setting is half-duplex. Please do not change the default setting without seek
User’s Manual 12 Switch no. Protocol Baud rate 00 VCL 9600 01 Pelco D 2400 02 Pelco P 4800 04 Chiper 9600 05 Philips
User’s Manual 13 (4) Power on again. 2.6 22-Pin Connector Definition A 50-cm data cable (as shown below) is supplied with th
User’s Manual 14 2.7 RS-485 Connector RS-485 is the interface that the PTZ Camera uses to communicate with its control unit. Co
User’s Manual 15 3. Operation and Configuration 3.1 OSD Display Format The information shown on the screen is described in t
User’s Manual 16 3.2 OSD Menu Tree The OSD setup menu structures for the 18×/26× model and the 22×/23×/35× model are listed sep
User’s Manual 17 Item Layer 1 Layer 2 Layer 3 Default PRESET RUN <001>~<256> ENTER EXIT YES ENTER SEQUENC
User’s Manual 18 Item Layer 1 Layer 2 Layer 3 Default SET YEAR <00> ~ <99> SET MONTH <01> ~ <12>
User’s Manual 1 Preface The information provided in this manual was current when published. The company reserves the right to
User’s Manual 19 Item Layer 1 Layer 2 Layer 3 Default MAX ANGLE <080 ~ 100 DEG> 90 SPEED BY ZOOM <ON>, <
User’s Manual 20 Item Layer 1 Layer 2 Layer 3 Default PRIVACY SWITCH <ON>, <OFF> OFF MASK SHADE <GRAY>,
User’s Manual 21 3.3 Configuration Menu The detailed functions and parameter settings for your PTZ Camera can be set in the O
User’s Manual 22 mentioned camera parameters. 3.3.3 BACKLIGHT The backlight compensation function prevents the central object
User’s Manual 23 3.3.4 FOCUS The focus on the PTZ Camera can be operated in two modes: Auto Focus mode and Manual Focus mode.
User’s Manual 24 • MANUAL In this focus mode, users can adjust the focus speed, ranging from 0 ~ 3. After completing setup
User’s Manual 25 from 00 ~ 31. SHUTTER With this option, SHUTTER speed takes main control of exposure, and both IRIS and AGC w
User’s Manual 26 • IRIS With this option, the priority of IRIS is higher than SHUTTER and AGC; SHUTTER and AGC circuit will fu
User’s Manual 27 from 3000K to 7500K. • INDOOR 3200 K base mode. • OUTDOOR 5800 K base mode. • ATW (Auto Tracing White B
User’s Manual 28 After WBC relevant parameter setups are completed, please exit the WBC MODE menu and go back to the Main Page 1
User’s Manual 2 Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means th
User’s Manual 29 NOTE: The difference between optical and digital zoom is that optical zoom uses the lens within the camera t
User’s Manual 30 Application: Users can see the displayed images, as shown below, when a dome is placed on the desk top in a con
User’s Manual 31 18×/26× Model: 22×/23×/35× Model: 3.3.8 SETUP MENU 2 18×/22×/23×/26×/35× Model:
User’s Manual 32 NOTE: To make the PTZ Camera tilt between a specific range, such as -10° to +100° or -10° ~ +190°, please go
User’s Manual 33 3.3.9 ID DISPLAY The user can choose whether the PTZ Camera ID will be displayed on the monitor to identif
User’s Manual 34 STEP 2: Turn on the OSD and go to the MAIN PAGE 2 to select <TITLE SETTING>. STEP 3: Select a number t
User’s Manual 35 STEP 3: Press <ENTER> again to save the defined preset point. Once completing setup of a preset point
User’s Manual 36 • SEQUENCE POINT Up to 32 points can be specified for each sequence line. The sequence points represent the or
User’s Manual 37 3.3.14 AUTOPAN Auto-pan means motion of scanning an area horizontally so that the PTZ Camera can catch horiz
User’s Manual 38 • SPEED This option is for defining the PTZ Camera rotation speed while running auto-pan. T
User’s Manual 3 Warning Notices • Handle the camera with care Do not abuse the camera. Avoid striking, shaking, etc. The came
User’s Manual 39 • RECORD START Follow the description to record the CRUISE path. 1. Rotate the PTZ Camera to the desired v
User’s Manual 40 • HOME FUNCTION The item is used to enable or disable the HOME function. Use the left/right direction keys o
User’s Manual 41 • GO If the HOME function is enabled, the user can execute the HOME function by selecting this option. • E
User’s Manual 42 algorithm. • MANUAL IR MANUAL ON Select the item to remove the IR blocking filter. IR MANUAL OFF Select the
User’s Manual 43 with an alarm system to capture images of a particular event. For wiring details, please refer to the install
User’s Manual 44 • PRESET POINT Select a preset point where the camera should go when an alarm pin is triggered. The preset poi
User’s Manual 45 If use 23× and 35× models, after exiting the ALARM SETTING menu, go back to the MAIN PAGE 3 to carry on setup
User’s Manual 46 INT FOCUS (Internal Focus) The alarm will be triggered if the internal focus changes; if the focus returns to t
User’s Manual 47 Backlight Compensation. • AUTO In this mode, the PTZ Camera will operate the WDR function automatically. •
User’s Manual 48 18×/26× Model: • PRIVACY SWITCH Users can enable or disable the Privacy Mask function through this item. Set
User’s Manual 4 Contents 1. Overview...
User’s Manual 49 H SIZE (00~80) Users can adjust the horizontal size of a privacy mask through this item. Set the H and V size
User’s Manual 50 • SHADE The color of a privacy mask can be selected through this item. The available colours are black, gray a
User’s Manual 51 1. Select the mask zone that will be erased (e.g. 01). 2. Press <ENTER> to confirm the selection. Conse
User’s Manual 52 • TIME DISPLAY Select <ON> to display time information on screen or <NO> not to display. • YEAR
User’s Manual 53 • SCHEDULE SWITCH Select <ON> to enable or <OFF> to disable the schedule function. • SCHEDULE
User’s Manual 54 3.3.24 EXIT OSD To exit the OSD setup menu, the user can either select this item on the bottom of MAIN PAGE 3
User’s Manual 55 Appendix A: Technical Specifications Items 35× Model CAMERA CCD Sensor 1/4" Progressive CCD Optical
User’s Manual 56 Item 22× Model 18× Model 23× Model 26× Model CAMERA NTSC 380k Effective pixels PAL 440k NTSC 480 TV l
User’s Manual 57 OSD Menu Notes The following OSD menu tables are provided for users to record various PTZ Camera setting. &l
User’s Manual 58 Item Layer 1 Layer 2 Layer 3 Notes PRESET POS. <001> ~ <255>, <END> SPEED <01>
User’s Manual 5 3.3.10 TITLE DISPLAY...
User’s Manual 59 Item Layer 1 Layer 2 Layer 3 Notes SET MINUTE <00> ~ <59> EXIT+SAVE SCHEDULE SWITCH
User’s Manual 60 <22×/23×/35× Model> Item Layer 1 Layer 2 Layer 3 Notes LANGUAGE <ENGLISH>, <FRENCH>, <
User’s Manual 61 Item Layer 1 Layer 2 Layer 3 Notes RECORD START ENTER RECORD END ENTER RUN CRUISE ENTER CRUISE E
User’s Manual 62 Item Layer 1 Layer 2 Layer 3 Notes <001> ~ <256> SEQUENCE SEQUENCE LINE <1> ~ <8>
User’s Manual 63
User’s Manual 6 1. Overview The ZC-PT series integrated indoor PTZ Camera is a new sub-compact model designed to deliver super
User’s Manual 7 The PTZ Camera provides 8 alarm inputs and 2 alarm outputs, and the smart alarm management mechanism can be pr
User’s Manual 8 • Multiple Built-in protocols • 8 alarm inputs, 1 alarm output • Flexible indoor and outdoor mountings • Com
Comments to this Manuals